New PATCH release 04.07.05

Changes since 04.07.04:
fix: macro pulse number is always 0 because not published
feat: publish trigger device status
fix: check for WORD_BOOST_STATUS

New PATCH release 04.07.04

Changes since 04.07.03:
fix: remove redundant PIEZO_ACTUATOR
fix: current conversion factor
feat: provide PIEZO_VOLTAGE and PIEZO_CURRENT via ZMQ

New PATCH release 04.07.03

Changes since 04.07.02:
feat: config for AMTF2

New PATCH release 04.07.02

Changes since 04.07.01:
fix: timer and location names for A1

New PATCH release 04.07.01

Changes since 04.07.00:

- fix: CMTB watchdog address

New MINOR release 04.07.00

Changes since 04.06.08:
chore: increase minor version number for new server release

New PATCH release 04.06.08

Changes since 04.06.07:
fix: operator GID for FLASH and XFEL

New PATCH release 04.06.07

Changes since 04.06.06:
feat: add FLASH
feat: config for the whole XFEL
fix: XFEL location names

New PATCH release 04.06.06

Changes since 04.06.05:
fix: deploy_firmware.py not writable fixup

New PATCH release 04.06.05

Changes since 04.06.04:
fix: watchdogAddress -> WATCHDOG_ADDRESS
fix: watchdog address
fix: deploy_firmware.py not writable

New PATCH release 04.06.04

Changes since 04.06.03:
feat: support firmware deployment and map file download via deploy tool
  - Only implemented for PZ16M

New PATCH release 04.06.03

Changes since 04.06.02:
- fix: compatibility to older TCK7 FW

New PATCH release 04.06.02

Changes since 04.06.01:
- chore: prepare for TCK7 FW 1.4.0
  * Hack: Enable write buffer swapping in init script. This does not solve
          all race conditions. Needs support in the server.
  * Change control table buffer after writing
  * Use applied table mode
  * use XDMA
  * change register name for DAQ area

New PATCH release 04.06.01

Changes since 04.06.00:
- feat: add PIEZO.ENA backward compitibility for PZ16M

New MINOR release 04.06.00

Changes since 04.05.02:
- fix: make work with server 04.06
  - change target parameter name from piezo_interface to peizoInterface (no underscore allowed)
  - make MACRO_ULSE_NUMBER uint64 to be compatible with periodic trigger module
- chore: bring PZT4 and PZ16M config more similar
  - remove math plugin from ADC_FREQUENCY to have both types int and value in Hz
-  feat: introduce internal trigger
  - requires piezo server 04.06
- fix USE_DOOCS_WATCHDOG boolean
- feat: add config for lbsync 26a
- fix: make pzt4 work with server 04.05
- adapt data types which were changed
- have PZ16M double buffering only show up in PZ16M config
- chore: switch PZT4 to version 1.2.0
fix: get values in initPZT4.py from settings
fix: make initPZT4 work for FMC20 and FMC25
fix: make test environment work with PZT4

BREAKING CHANGE:  uses MEM_MULTIPLEXED syntax instead of AREA_MULTIPLEXED and has different size. Older versions of PZT4 fiwmare are not supported any more

New PATCH release 04.05.02

Changes since 04.05.01:
feat: introduce dac slope limiters on CMTB
chore: Eliminate FULL_STATION_NAME variable

New PATCH release 04.05.01

Changes since 04.05.00:
- fix: PZ16M HV bit from lated register is broken
  Take the HV bit from the unlatched register. It is broken in the latched register and the PEM protection would trigger anyway if the HV failed, so it is safe to take the unlatched bit.

New MINOR release 04.05.00

Changes since 04.04.00:
- fix: x-axis scaling for ctable spectrum
- fix: daq table length and strobe divider for long pulse
- feat: enable read double buffering for the PZ16M
- fix: make dacVoltage and dacVoltageOffThreshold double

New MINOR release 04.04.00

Changes since 04.03.06:
feat: make control table strobe configurable for PZ16M
fix: control table frequency for PZ16M
fix: conversion factors for voltages
feat: add device status to board location
chore: make doocs data types compatible with llrfpiezo3
feat: use WORD_STATUS_LATCH for PZ16M
feat: make UNMAPPED location optional
feat: add configuration for CMTB multi cavity
chore: add map file for testing in real hardware
fix: properly configure techlabcpullrfdev to TEST.RF
feat: split timer into separate xlmap device
fix: variable name in pzt4 xlmap

New PATCH release 04.03.11

Changes since 04.03.10:
- feat: make control table strobe configurable for PZ16M
- CMTB MCAV is at 1024 Hz adc/dac frequency for 1 Hz CW operation